Mazda 3 engine diagram

Mazda 3 engine diagram - typical Mazda 3 engine diagrams, parts and component assemblies

Mazda 3 - the car of small middle class C. The premiere of the car has taken place in 2003, and in 2006 Mazda 3 has passed insignificant restyling which has been shown on the Geneva motor show. Mazda 3 involves with the stylish appearance, dynamism and manoeuvrability. Mazda 3 has united in itself the best qualities promoting success of its predecessors. It has been developed to erase the sides traditionally dividing classes of cars, and to offer consumers of a class C more in respect of design, style, quality and internal saturation.

Mazda 3 engine diagram - engines L3, L8, LF

Mazda 3 engine diagram - cylinder block head diagram

Mazda 3 engine diagram - cylinder block diagram

Read more...

Ford Taurus engine diagram :: engine maintenance and repair manuals

Ford Taurus engine diagrams - Ford Taurus engine maintenance and repair manuals

The description of repair procedures. Spent with a condition, that the engine is established in the car. For the engine removed from the car and established at the stand, many recommendations are inapplicable. Repair operations, admissible at the engine not removed from the car: layer pads of inlet and final collectors, an oil sump and heads of cylinders are accessible at not removed engine. External details of the motor - inlet and final collectors. (And the pump), a water pump, a starter, the generator, the distributor of ignition and system of injection of fuel it-is possible to remove an oil sump for repairing, not removing the engine As the cylinder block head can be removed, not touching the engine also the valve too it is possible to serve in the same position. In the absence of the necessary equipment for engine removal, not removing the engine it is possible to carry also out repairs and replacement of piston rings, buckets, connecting rods and bearings of connecting rods.
Removal and installation of rocker arm covers:

Ford Taurus engine diagram - the parts diagram of Ford Taurus engine 3.0L V6 rocker arm cover

1 - knot rocker arm covers (right); 2 - hairpins; 3 - the screw with a hollow disk; 4 - sealing (two places from each party); 5 - knot rocker arm covers (left); 6 - fn arrangement of pins; 7 - a rocker gear cover gasket; 8 - a front part of the engine; 9 - knot of an intake manifold 4.0 - 6.0 mm (15 - 23 inches); 10 - knot of a head of the cylinder block.

Ford Taurus engine diagram - the parts diagram of Ford Taurus engine 3.8 LV6 rocker arm cover

1 - the bolt, is required 2 pieces; 2 - rocker arm cover knot; 3 - the hairpin, is required 2 pieces; 4 - a layer pad; 5 - knot of a head of the cylinder block; 6 - a front part of the engine.

Read more...

Engine Diagram :: how and where to search for engine diagram

Where to find the engine diagram of my car? There were problems with my motorcycle where to find the engine diagram?

Familiar questions. Everyone who has decided to refuse services of automobile service and to repair the car, motorcycle or ATV in house garage, necessarily faced this problem. The answer arises by itself - to search it is necessary on the Internet. On the Internet it is possible to receive in some minutes not only the engine diagram, but also the full manual of its repair. It will allow you to save time and money.
The main sources of such information are forums and blogs (like this) on a theme of search of failures and repair of engines. It is possible to take advantage still of answer sites though these sites helped me seldom. How to find the necessary site? If you search for the engine diagram of your car or a motorcycle, never it is necessary to search engine diagram. In this case, you receive more than 8 000 000 sites, will practically find among which necessary to you not probably. It is necessary to try to ask a question as much as possible particularly. For example, ford engine diagram, ford focus engine diagram or even ford focus 1995 engine diagram. The more particularly a question, the more likely you will find the scheme of the engine necessary to you. Try to ask a question ford focus 1,8 l Zetec-E engine diagram and look, that will turn out...
But happens and so what to find the necessary engine diagram all the same it is impossible. In this case search for repair manual. Each repair manual necessarily contains all necessary schemes, including the engine diagram of your car or ATV.
Search, find and load. Also be not afraid to repair the engine independently - at you necessarily it will turn out.

Read more...

Volvo engine diagram :: Volvo S40 engine diagram

Volvo engine diagram - Volvo S40 engine diagram, parts and component assemblies

Engines V4204S and В4184S - four-cylinder, 16-valves. Structurally engines identical. It is possible to complete both engines both with automatic, and with mechanical transmission. At a variant of a complete set with mechanical transmission engine V4184S is packed with transmission JB3, and engine V4204S - with transmission JС5. Both engines can work with automatic transmission Aisin Warner 50-42. In both engines engine control system Fenix 5.1 identical designs is applied. Engine fastenings are located on the right on the right internal bumper, at the left on the left longeron and on the central longeron in front and behind.
Volvo engine diagram - a typical schematic of the 1998-2002 Volvo V40 engine diagram

1 - cylinder block; 2 - cylinder head; 3 - head gasket; 4 - cover; 5 - intake valve; 6 - exhaust valve; 7 - valve seats; 8 - valve seals; 9 - valve springs; 10 - valve spring seats; 11 - valve spring locks; 12 - valve lifters; 13 - camshaft; 14 - camshaft seal; 15 - front cover; 16 - camshaft gear; 17 - crankshaft gear; 18 - timing belt; 19 - tensioner; 20 - idler pulley; 21 - damper; 22 - piston rings; 23 - piston; 24 - connecting rod; 25 - bearings; 26 - bearing set; 27 - crankshaft; 28 - rear main seal; 29 - vibration damper; 30 - oil pan; 31 - oil pump; 32 - oil pick-up.

Read more...

Subaru engine diagram :: Subaru Legacy engine diagram

Subaru engine diagram - Subaru Legacy engine diagram - cylinder block heads

Subaru engine diagram - head of the engine 2,2 l basic block

Subaru engine diagram - sequence of a tightening of bolts of fastening of cylinder block head

Subaru engine diagram - sequence of a tightening of bolts of fastening of cylinder block head on the engine of 1,8 l

Removal of cylinder block head
1. Remove pressure in a fuel system and a wire of weight from the accumulator.
2. Merge a cooling fluid from a system cooling and unscrew spark plugs.
3. Remove a toothed belt, pulleys of a cam shaft and internal housings of a toothed belt. Remove covers of a head of the cylinder block and assembly of rocker actuators (the engine 1,8 l and 2,2 l) or cam shafts (the engine 2,5 l).
4. Unhook exhaust pipes from cylinder block heads.
5. Remove an intake manifold.
6. Unscrew front engine bearers and, using a jack, through a board hoist the engine.
7. On an engine left side unscrew an exhaust gas recirculation tube.
8. Working in sequence, return shown on fig. Sequence of a tightening of bolts of fastening of a head of the cylinder block, turn off bolts of fastening of a head of the cylinder block on 1/3 turns for each pass before full unscrewing of bolts.
9. Remove a cylinder block head.

Read more...

Lexus engine diagram :: Lexus RX300 engine diagram

Lexus engine diagram - Lexus RX300 engine diagram - the general information

3.0 l V-shaped 6-cylinder 24-valves Lexus RX300 engine 1MZ-FE with four (on two on each number of cylinders), located from above, cam shafts are established cross-section in a front part of the car. The automatic transmission is located at the left. Inlet and outlet valves are resulted from cam shafts through pushers. Valves are located in the guide bushes inserted into a head of the block, as well as a saddle of valves. Cam shafts are located in heads of the cylinder block and resulted in rotation from a bent shaft by means of a belt. In each number of cylinders one cam shaft puts in action inlet valves, and another - outlet valves. The pump of system of cooling is located on a right side of the cylinder block and resulted by belt ГРМ. For preparation mixture fuel-air serves electronic system of injection of fuel. Necessary for ignition of a mixture the spark is created by the noncontrollable ignition system. Oil in a lubricating system moves under pressure by means of the pump. On the pressure head party of the oil pump the valve which opens at excess of pressure above the established value is established and allows oil parts to flow down back in a crankcase oil pan. Oil is soaked up from a crankcase through an oil tray. The pump directs oil to the replaceable full-flow filter. At a blockage of an oil filter the valve directs oil directly to the main port bypassing the filter.
Lexus engine diagram - Lexus RX300 cylinder block (the components interfaced to the cylinder block)

1 - a socket of the gauge of a detonation, 2 - the detonation gauge, 3 - a socket, 4 - an inlet nozzle, 5 - wiring harnesses, 6 - an engine wiring, 7 - a drain plug, 8 - a layer pad, 9 - a water pump, 10 - a bracket of a roller of a belt of drive gear GDM, 11 - a sealing gasket of system of cooling, 12 - a drain plug of oil of the engine, 13 - an oil filter clutch, 14 - an oil filter, 15 - a ring gasket, 16 - the oil pump, 17 - the gauge for measurement of pressure of oil of the engine, 18 - a socket of the gauge 17, 19 - a compressor bracket, 20 - the top section of a crankcase oil pan, 21 - a gauge socket, 22 - a front epiploon of a bent shaft, 23 - the generator, 24 - oil-collection, 25 - the bottom section of a crankcase oil pan.
Lexus engine diagram - Lexus RX300 cylinder block assembly

1 - a piston ring, 2 - a piston ring, 3 - oil-control ring plates, 4 - a retaining ring, 5 - a finger, 6 - the connecting rod barrel, 7 - an oil ring expander, 8 - the bucket, 9 - a hollow disk, 10 - a connecting rod, 11 - bearing inserts, 12 - a bearing cap, 13 - a rear epiploon of a bent shaft, 14 - a main bearer cover, 15 - a cover of an epiploon 13, 16 - the cylinder block, 17 - the top liner of a main bearer, 18 - the top thrust washers, 19 - the bottom liner of a main bearer, 20 - a bent shaft, 21 - the bottom thrust washers.

Read more...

Citroen engine diagram :: Citroen Xantia engine diagram :: Belt of drive gear GDM

Citroen engine diagram - Citroen Xantia engine diagram - belt of drive gear GDM - the general information, removal, check of a condition and installation

By means of a gas-distributive belt the camshaft drive, a high pressure and water pump fuel pump is carried out. Rotation is transferred through tooth gears from the front end of a bent shaft. Remember that breakage or a tension of a gas-distributive belt at the working engine leads to major damages of a head of cylinders as a result of blow of plates of valves about the bottoms of buckets. Replacement of a gas-distributive belt should be made strictly according to the schedule of routine maintenance of the car. Extraordinary replacement of a belt should be made in case of pollution by its oil, and also at occurrence of the scraping sounds testifying to non-uniform deterioration of a tape or teeths. Simultaneously with belt change it is necessary to check up a water pump on presence of signs of escapes.
Citroen engine diagram - Citroen Xantia engine diagram - removal of a belt of drive gear GDM

8 - a square bore, 9-11 - bolts, 12 - an axial nut, 13 - an adjusting bolt.

Read more...

Jeep engine diagram :: Jeep Grand Cherokee engine diagram

Jeep engine diagram - Jeep Grand Cherokee engine diagram - bent shaft removal

Bent shaft extraction can be made only after the engine will be removed from the car. It is supposed also, that a flywheel/privodnoj the disk, the snubber of shifting jerkss, a distributive chain, a crankcase oil pan, the oil pump and shatunno-piston assemblies are already removed from the engine.
Jeep engine diagram

Definition of an axial backlash of a bent shaft by means of a measuring instrument.
Jeep engine diagram

Measurement of size of an axial backlash of a bent shaft by means of a probe.
Jeep engine diagram

Covers of main bearers are usually numbered in front back on the engine (marksman) - on engines V8 in volume of number of 5.2 l are located on the passenger party of covers.

Read more...

Mercedes engine diagram :: Mercedes-Benz Sprinter engine diagram

Mercedes engine diagram - Mercedes-Benz Sprinter engine diagrams

Mercedes engine diagram - Mercedes-Benz Sprinter engine basic block
To the cylinder block attach the majority of the basic units necessary for work of the engine, such as the generator, a starter, a fuel pump. The cylinder block heel forms an engine crankcase. On both types of engines replaceable sleeves of cylinders which can be replaced if degree of deterioration of cylinders exceeds as much as possible admissible limit are established.
Mercedes engine diagram - Mercedes-Benz Sprinter the details established on the cylinder block

1 - the connecting union; 2 - a carving nozzle; 3 - the union for cooling fluid offtake, on the right side; 4, 5 - ring gaskets; 6 - a cylinder block plug; 7 - the cylinder block; 8 - a ball blocking an oil highway behind; 9 - a flange of a rear cuff of a bent shaft; 10 - a rear cuff of a bent shaft; 11 - a bolt of fastening of a flange of a rear cuff of a bent shaft to the cylinder block; 12 - an elastic hollow disk; 13 - oil-spraying a nozzle of system of cooling of the buckets, new execution; 14 - a hexagon-head bolt; 15 - oil-spraying a nozzle of system of cooling of buckets, out-of-date execution; 16 - a bolt of fastening of a cover of a main bearer; 17 - a main bearer cover; 18 - the landing barrel of a cover of the gear of a camshaft drive; 19 - a plug for closing of the oil port ahead; 20 - a ball locking an oil highway ahead; 21 - the union for joining of a tube of giving of lubricant on a chain; 22 - a tube of giving of lubricant on a chain; 23 - a ring gasket nozzle oil-spraying on the block; 24 - a screw plug on the left side; 25 - a ring gasket.
Mercedes engine diagram - Mercedes-Benz Sprinter cylinder block rear

Rear of the cylinder block with instructions of a site of the steel ball (1) blocking the main oil highway, and plugs (2) cylinder blocks.
Mercedes engine diagram - Mercedes-Benz Sprinter front part of the cylinder block

1 - a pin of a tension of a spring; 2 - a basic finger of the gear of a chain; 3 - a steel ball in diameter of 17 mm; 4 - oil-spraying a nozzle; 5 - a cylinder block plug; 6 - a basic finger of a boot of a chain tensioner; 7 - a basic finger of the gear of a chain of a drive gear of the oil pump.

Read more...

Daewoo engine diagram :: Daewoo Matiz engine diagram

Daewoo engine diagram - Daewoo Matiz engine diagram
Daewoo Matiz engine four-cycle, with water cooling and three cylinders with a working volume of 769 sm3 (68,5х72,0 mm). Engine lubricant is carried out under the pressure created by the oil pump, located on cranked to a shaft from a crankshaft pulley.

Daewoo engine diagram - arrangement of elements of a lubricating system of Daewoo Matiz engine

a - a crankshaft pulley; b - the oil pump; c - the port; d - the bucket; f - rocker actuators; k - a cam shaft; l - the valve; m - the port; n - an oil filter; o - oil-reception a tube.
The cylinder block head is executed from a cast aluminium alloy for improvement of strength, hardness and weight reduction. The cam shaft and a rocker pivot are located linearly. The cylinder block the greatest detail of the engine, to its external surface all necessary details fasten. In the cylinder block there are bores for prevention of an overheat and for cylinder block lubricant.
Daewoo engine diagram - cylinder block and valve head

a - an inlet valve; b - a shaft of rocker actuators; c - a rocker actuator; d - a cam shaft; е - an outlet valve.
It is made of the elastic strengthened rubber and does not demand some lubricant. Daewoo Matiz engine mount is intended for absorption or kickdown of vibration of the engine and pushes from roughnesses of a road carpet. The engine mount is fixed in front, rear and right parts of the engine, and one suspender is attached from a gear box.

Read more...

BMW engine diagram :: BMW 3 (E46) engine diagrams :: Part 2

BMW engine diagram - BMW 3 (E46) engine diagrams (Part 2)
BMW engine diagram - BMW 3 (E46) engine M52TU (320i, 323i, 328i) diagram

1 - an ignition coil; 2 - the oxygen gauge; 3 - the catalytic converter; 4 - V belt; 5 - a clutch; 6 - the cooling fluid pump; 7 - a thermostatically controlled chamber; 8 - block VANOS; 9 - a hydropusher; 10 - cam shafts.
6-cylinder gasoline engine M52TU has a head of cylinders and the cylinder block from an aluminium alloy. The alloy has the improved heat conductivity and smaller weight in comparison with pig-iron. 4-klapannaja the head of cylinders has two cam shafts with a drive gear from a chain with the gear of regulation of cam shafts VANOS. Thus both cam shafts depending on number of revolutions and engine loading turn concerning a corresponding sprocket so that to receive the optimum moment of opening of valves. The knot is steered from an engine monitor.br>BMW engine diagram - M52TU engine parts diagram

1 - a cylinder block head; 2 - cam shaft bed; 3 - a layer pad of a head of the cylinder block; 4 - a camshaft cover; 5 - a cover of a head of the cylinder block; 6 - a moulding; 7 - a layer pad; 8 - a layer pad; 9 - an outlet valve; 10 - an inlet valve; 11 - oil-reflective caps of valves; 12 - the bottom saddle of a valve spring; 13 - valve springs; 14 - the top saddle of a valve spring; 15 - crackers; 16 - hydropushers of valves; 17 - cam shafts; 18 - block VANOS; 19 - cover of GDM; 20 - a front epiploon of a bent shaft; 21 - cover gaskets of drive gear og GDM; 22 - chain VANOS; 23 - sprockets of camshafts; 24 - the top chain tensioner; 25 - the chain gear; 26 - a chain of drive gear of GDM; 27 - a camshaft sprocket; 28 - a bent shaft sprocket; 29 - a chain tensioner boot; 30 - the chain gear; 31 - a chain tensioner; 32 - piston rings; 33 - a piston finger with retaining rings; 34 - a connecting rod with the barrel of the top head, a cover and bolts; 35 - connecting rod liners; 36 - radical liners; 37 - a bent shaft; 38 - a rear epiploon of a bent shaft; 39 - the snubber of shifting jerkss; 40 - a crankshaft pulley; 41 - a nave; 42 - a bent shaft sprocket; 43 - a crankcase oil pan; 44 - a layer pad; 45 - the oil pump; 46 - oil pump pinion gears; 47 - an oil pump sprocket; 48 - a chain of a drive gear of the oil pump.

Read more...

Peugeot engine diagram :: Peugeot gasoline and diesel engines diagrams

Peugeot engine diagram - Peugeot gasoline and diesel engines diagrams
Peugeot engine diagram - Peugeot gasoline engine (8 valves) sectional views

The engine is four-cycle, four-cylinder with a cross-section arrangement in a front part of the car. Engines with a working volume of 1905 sm3 and 1998 sm3 with 16 valves have two top cam shafts. On all Peugeot models the water pump puts in action a toothed belt of a drive gear of system of a gas distribution. Lubricant - under the pressure created by the oil pump which is resulted by a chain from the right end of a bent shaft. On Peugeot models with 16 valves there is an oil cooler which is established under an oil filter. The engine code is backed out on a plate attached to the right front part of the engine basic block, on the engine with a working volume of 1761 sm3 is backed out directly on a cylinder block front face, and on the engine of 1998 sm3 - to the left of an oil filter.
Peugeot engine diagram - Peugeot gasoline engine TU3 sectional views

a - cross-section, b - longitudinal section.
Cars Peugeot 405 gasoline engines with a working volume of 1,4 l since 1993 prepare in Poland with a version of equipment GL. The basic differences (in comparison with earlier described cars Peugeot) consist in application of the engine (family TU), and also transmission (type МА) with the design differing from earlier described models.
Peugeot engine diagram - Peugeot diesel engine XUD 9 sectional views

Peugeot diesel engines are four-cycle, four-cylinder. Engine fastening - cross-section ahead of the car with an inclination back on 30 degrees. Placed in a head of the cylinder block the cam shaft is set in motion by a toothed belt. These engines have water cooling.

Read more...

BMW engine diagram :: BMW 3 (E46) engine diagrams :: Part 1

BMW engine diagram - BMW 3 (E46) engine diagrams (Part 1)
BMW engine diagram - BMW 3 (E46) engine M43TU (316i, 318i) diagram

1 - a cover of a head of cylinders; 2 - a cam shaft; 3 - a roller rocker actuator; 4 - the hydraulic compensator bar of a spacing in valves; 5 - a spark plug; 6 - a balancing shaft; 7 - the cooling fluid pump; 8 - a thermostatically controlled chamber; 9 - V belt; 10 - an oil filter; 11 - the generator; 12 - the inlet pipe duct with the throttle valve case.
4-cylinder gasoline engine M43TU in volume of 1.9 l - 2-klapannyj, with a cam shaft located. From above the cam shaft is resulted in rotation by a chain. Valves are set in motion through a roller rocker actuator. For indemnification of vibration of the engine two balancing shaft, located under a bent shaft serve. A drive gear of valves - roller. An inlet path with changeable length DISA.
BMW engine diagram - BMW 3 (E46) engine M47 (320d) diagram

1 - cam shafts; 2 - a roller rocker actuator; 3 - the soaking up filter; 4 - the catalytic converter; 5 - a turbo-compressor; 6 - V belt; 7 - the generator; 8 - chains of drive gear of GDM; 9 - the vacuum pump; 10 - a spray jet.
In 4-cylinder turbodiesel М47 two cam shafts with the top arrangement have a chain drive gear and influence valves through a roller rocker actuator. The second chain actuates a high pressure fuel pump. A drive gear of valves - roller. The diesel engine has a turbo-supercharging with changeable geometry of the turbine (VTG) and cooling of submitted air. The head of cylinders is made of an aluminium alloy. The engine is supplied by the oxidising catalytic converter and system of recirculation of the fulfilled gases.

Read more...

Renault engine diagram :: 1,8 l 16-valves engine diagrams

Renault engine diagram - Renault gasoline 1,8 l 16-valves engine diagram

1 - a bearing part of the right amortisation rack of the chassis; 2 - a housing of the accumulator battery; 3 - a cross-section beam; 4 - protection of candles and wires of ignition against a moisture; 5 - a reception tube of the muffler; 6 - a cover mouth oil-bulk; 7 - the ignition distributor; 8 - an ignition coil with the ignition module; 9 - the pressure control device; 10 - a tank for a brake liquid; 11 - an expansion chamber of system of cooling; 12 - the electromagnetic valve of ventilation of a tank; 13 - the electronic controller of injection of fuel and timing control; 14 - a tank of the window washer of front and rear glasses; 15 - a tank of the servo mechanism of a steer; 16 - a distributive fuel line with valves of injection and a fuel pressure regulator; 17 - an intake manifold; 18 - a probe of measurement of level of oil; 19 - the engine of the fan of a system cooling; 20 - the case of a throttle valve of the device of multidot injection of fuel; 21 - an air filter; 22 - the additional block of the relay.
Renault engine diagram - Renault 16-valves engine in a sectional view

1 - the ignition distributor; 2 - a cam shaft with hydrocompensator bars; 3 - spark plugs; 4 - an outlet valve; 5 - a collector of release of the fulfilled gases; 6 - the bucket; 7 - a bent shaft; 8 - a crankcase oil pan; 9 - an intake manifold; 10 - a pulley of an inlet cam shaft; 11 - a temperature detector of soaked up air; 12 - a toothed belt; 13 - the generator; 14 - a V belt; 15 - a pulley of the pump of a cooling fluid; 16 - a soaking up mouth of the oil pump.

Read more...

Ford engine diagram :: Ford Focus engine diagram

Ford engine diagram - Ford Focus gasoline and diesel engines diagrams
Ford Focus complete with gasoline engines of 1,4 l Zetec-SE capacity of 55 kw (75 h.p.), 1,8 l Zetec-E capacity of 85 kw (115 h.p.) and two turbo-diesel engines with volume 1,8 l, capacity of 55 kw (75 h.p.) or 66 kw (90 h.p.).

Ford engine diagram - the cylinder block of engines of series Zetec-SE consists of an aluminium alloy alloyed by silicon

1 - the cylinder block; 2 - liners of main bearers; 3 - a bent shaft; 4 - a cover of main bearers.
Ford engine diagram - Ford Focus cam shaft

1 - a final cam shaft; 2 - an inlet cam shaft; 3 - an inlet valve; 4 - an inlet channel; 5 - a combustion chamber; 6 - a discharge port; 7 - an outlet valve.
Ford engine diagram - Ford Focus cylinder working volume

1 - the top wall of a combustion chamber; 2 - a clearance volume; 3 - the top dead point; 4 - the bottom dead point; 5 - a cylinder working volume.

Read more...

Renault engine diagram :: 1,9 l diesel engine diagrams

Renault engine diagram - Renault 1,9 l diesel engine diagram

1 - a bearing part of the right amortisation rack of the chassis; 2 - a housing of the accumulator battery; 3 - a cross-section beam; 4 - a cover mouth oil-bulk; 5 - an intake manifold; 6 - the valve of system of recirculation; 7 - the vacuum pump of the booster of a brake drive gear; 8 - the controller of preliminary heating; 9 - a tank for a brake liquid; 10 - an expansion chamber of system of cooling; 11 - the additional block of the relay; 12 - a tank of the window washer of front and rear glasses; 13 - a fuel filter; 14 - the right part of the pendant device of the engine; 15 - the generator; 16 - a high pressure fuel pump; 17 - a tank of the servo mechanism of a steering; 18 - a probe of measurement of level of oil; 19 - the thermostatically controlled chamber case; 20 - a gear box; 21 - an air filter; 22 - air mains of cooling of forced air.
Renault engine diagram - Renault diesel engine in a sectional view

1 - an intake manifold; 2 - the vacuum pump of the booster of a brake drive gear; 3 - a cam shaft; 4 - the valve with a spring and a pusher; 5 - buckets; 6 - a connecting rod; 7 - a flywheel with clutch; 8 - a bent shaft; 9 - the generator; 10 - a high pressure fuel pump; 11 - a housing of a gear drivebelt.

Read more...

Saab 95 engine diagram :: 6-cylinder diesel engine diagram

Saab engine diagram - Saab 95 6-cylinder petrol engine diagrams

3.0 l V-shaped 6-cylinder 24-valves diesel engine with direct injection of fuel are established cross-section in an impellent compartment. The engine is completely made of aluminium. Polishing of the block and a head of cylinders are not admissible. Fuel moves to spray jets on the general fuel highway. Spray jets spray certain quantity of fuel and during the certain moment, separately for each cylinder. The quantity and the fuel delivery moment pay off an electronic control package the engine (ECM). The throttle case, thus, is absent. Is absent as well the ignition system.
Saab engine diagram - Saab 95 lubricating system of the diesel engine diagram

1 - a cam shaft of the right head of cylinders, 2 - a cam shaft of the left head of cylinders, 3 - the vacuum pump, 4 - the cam shaft bearing, 5 - a head of the right cylinder block, 6 - a head of the left cylinder block, 7 - oil-spray (transmission), 8 - an idler pinion (transmission), 9 - oil-cooler, 10 - an oil filter, the valve, 11 - an oil filter, the basic stream, 12 - an oil filter, the valve, 13 - a crankcase, 14 - the gauge of level of impellent oil, 15 - a crankcase oil pan, 16 - an oil tray, 17 - the oil pump, 18 - oil-cooler, 19 - the valve, 20 - a turbo-compressor, 21 - a bent shaft main bearer, 22 - oil-spray (under the bucket), 23 - the bent shaft bearing, 24 - the bucket, 25 - a piston finger.
The diesel engine lubricating system is similar to a lubricating system of gasoline engines (Saab 95 engine diagram :: 4-cylinder gasoline engine diagram, Saab 95 engine diagram :: 6-cylinder petrol engine diagram).
Saab engine diagram - Saab 95 arrangement of bearing parts of the diesel engine

The engine is established on four bearing parts, two of which - hydraulic type.

Read more...

Toyota Camry engine diagram :: 4-cylinder engine - details of a head of the engine basic block 5S-FE

Toyota engine diagram - Toyota Camry 4-cylinder engine - details of a head of the engine basic block 5S-FE

1 - an eyelet for engine lifting; 2 - the grounding tyre; 3 - a generator bracket; 4 - a layer pad of a head of the cylinder block; 5 - a rear housing of a toothed belt; 6 - a lockwasher; 7 - a stop ring; 8 - a hollow disk; 9 - a ring gasket; 10 - a cam shaft pulley; 11 - covers of bearings of a cam shaft; 12 - brackets of support of an intake manifold; 13 - tubes and ASV; 14 - vacuum tubes; 15 - VSV for EGR; 16 - valve EGR and the vacuum modulator; 17 - layer pads; 18 - layer pads; 19 - the throttle case; 20 - an intake manifold; 21 - a layer pad; 22 - a layer pad; 23 - a layer pad; 24 - the absorber of a pulsation of fuel; 25 - a submitting fuel hose; 26 - a returnable fuel hose; 27 - fuel delivery tubes; 28 - a ring gasket of round section; 29 - a ring gasket; 30 - a fuel injection nozzle; 31 - a ring gasket; 32 - a bracket; 33 - valve PCV; 34 - a cover of a head of the cylinder block; 35 - layer pads; 36 - a ring gasket; 37 - oil-reflective a cap; 38 - a cam shaft steering inlet valves; 39 - spark plugs; 40 - a cam shaft steering outlet valves; 41 - an adjusting layer pad; 42 - a cam follower; 43 - crackers; 44 - the top plate of a spring; 45 - a spring; 46 - a spring seat; 47 - a stop ring; 48 - a valve guide bush; 49 - an eyelet for engine lifting; 50 - the distributor; 51 - a branch pipe of system of cooling; 52 - a layer pad; 53 - an oil pressure sensor; 54 - a bypass pipe of system of cooling; 55 - the is warm-isolating screen; 56 - a layer pad; 57 - an exhaust manifold; 58 - the is warm-isolating screen of an exhaust manifold; 59 - a layer pad; 60 - a clamper; 61 - a layer pad; 62 - the catalytic converter; 63 - a thermal protection of the catalytic converter; 64 - a bracket of the catalytic converter; 65 - a thermal protection of the catalytic converter; 66 - the bottom thermal screen of an exhaust manifold; 67 - a cylinder block head; 68 - a layer pad; 69 - a ring gasket of round section.

Read more...

Renault engine diagram :: Engine 1,8 l type «F» diagrams

Renault engine diagram - Renault gasoline engine 1,8 type «F» diagram

1 - a bearing part of the right amortisation rack of the chassis; 2 - a housing of the accumulator battery; 3 - a cross-section beam; 4 - a cover mouth oil-bulk; 5 - the lever of a throttle valve with a bearing part of a rope of a throttle valve; 6 - an air intake of the device of the injection located more low; 7 - hoses of ventilation of the engine; 8 - an ignition coil with the ignition module; 9 - the vacuum gauge of an intake manifold; 10 - a tank for a brake liquid; 11 - an expansion chamber of system of cooling; 12 - the electromagnetic valve of ventilation of a tank; 13 - the electronic controller of injection of fuel and timing control; 14 - a tank of the window washer of front and rear glasses; 15 - the generator; 16 - a tank of the servo mechanism of a steer; 17 - a probe of measurement of level of oil; 18 - the engine of the fan of a radiator; 19 - the air conditioner pipe duct; 20 - the ignition distributor, 21 - the air filter case; 22 - the additional block of the relay.
Renault engine diagram - Renault 1,8-litre F-engine in a sectional view

1 - branch pipes of an inlet gas pipeline; 2 - the carburettor; 3 - branch pipes of a supply and a conclusion of air from the engine; 4 - an exhaust manifold of the muffler; 5 - a flywheel; 6 - a cam shaft; 7 - an inlet valve; 8 - a pulley of a toothed belt of a cam shaft; 9 - a toothed belt tension roller; 10 - the generator; 11 - a toothed belt drive roller; 12 - a pump pulley; 13 - a pulley of the pump of a cooling fluid; 14 - a crankshaft pulley; 15 - a connecting rod; 16 - an additional shaft of the oil pump.

Read more...

Mitsubishi Galant engine diagram :: removal and installation of assemblies of a drive gear of valves

Mitsubishi engine diagram - removal and installation of Mitsubishi Galant assemblies of a drive gear of valves

Mitsubishi engine diagram - Mitsubishi Galant components of assembly of a drive gear of valves of engines of 1.5 l

1 - a breather branch pipe, 2 - hose PCV, 3 - a cover of a head of cylinders, 4 - a sealing gasket, 5 - an epiploon, 6 - assembly of a drive gear of valves, 7 - assembly of a drive gear of valves, 8 - rocker actuators D, 9 - a wavy hollow disk, 10 - remote barrels, 11 - rocker actuators With, 12 - a shaft of rocker actuators of a drive gear of outlet valves, 13 - rocker actuators In, 14 - springs of rocker actuators, 15 - rocker actuators And, 16 - a shaft of rocker actuators of a drive gear of inlet valves, 17 - an adjusting screw, 18 - a nut, 19 - a cam shaft.
Mitsubishi engine diagram - Mitsubishi Galant components of assembly of a drive gear of valves of engines of 1.8 l

1 - a breather branch pipe, 2 - hose PCV, 3 - a cover of a head of cylinders, 4 - a sealing gasket, 5 - an epiploon, 6 - an epiploon, 7 - assembly of a drive gear of valves, 8 - assembly of a drive gear of valves, 9 - springs of a shaft of rocker actuators, 10 - rocker actuators And, 11 - rocker actuators In, 12 - a shaft of rocker actuators of a drive gear of inlet valves, 13 - an adjusting screw, 14 - a nut, 15 - rocker actuators With, 16 - a shaft of rocker actuators of a drive gear of outlet valves, 17 - an adjusting screw, 18 - a nut, 19 - a cam shaft.

Read more...